Building Design can be tricky, it sometimes seems a slow exercise of trial and error. Not being able to calculate the metrics for your project until you are done designing it can be a nuissance. If only we could wish for the some features in our project and have a design and its metrics in a few seconds… Oh! Wait. It turns out you can… Read on to find out how Architechtures con boost your efficiency.
How to customize the parameters for Automated Building Design and BIM Modeling.
As explained previously, at the Site Planner Level there are some options allowing us to change the size of buildings. However, the main function of the site planner is to place them on the plot, customizing them is done at the Building Level.
View Modes and Breadcrumb Levels
In Plan view mode there really isn’t a Building level view. Instead the Floor view is used. By default when you enter a building view you will see the standard floor view. We can change the view to any floor of the building using the breadcrumb.
In the Model and Cost view modes the Floor view level is not reached. The limit of the Model and Cost view modes is the Building view mode.
Edit Modes Priorities
In the Site view there is no distinction between Auto, Assisted or Manual editing mode. In the Building view, however, the distinction between editing modes is of primary importance.
To avoid losing some of the work done we must progress from Auto to Assisted to Manual mode, never the other way around. We must exhaust the configuration options in the Auto editing mode before moving on to Assisted. And again, exhaust those in Assisted mode before moving on to Manual. To do this, it is necessary to understand what kind of design options are found in each editing mode.
Building – Data Panel
In the Building view we still have available all the sections already seen in the Site view. This allows us to see how the changes we make at the Building level affect the project as a whole.
In addition to the sections already seen in the Site view, two new ones are added in a familiar format:
The Building´s Area Schedule
This has exactly the same format as the Plot Area Schedule. Except that only the areas of the currently selected building are displayed.
The Building´s Housing Mix
The upper half is the same as in the Site view: An account of the total dwelling units grouped by number of bedrooms. But the bottom half is different. At the site level there is an account of dwellings grouped by number of bedrooms, both by building and for the whole plot. Whereas at the building level it compares the housing mix obtained in the selected floor with the one required by the user.
Finally, a new section is added. It consists of a list of all the typologies present in the selected floor with their most relevant areas and ratios.
Building – Input Panel – Editing Mode Auto – AI Powered:
Here is where the composition and size of the target dwellings is defined. We have one for each flat typology, from 1 to 4 bedrooms.
There are three types of configuration options:
These are used to define the ideal target area for each room.
Here you define which rooms you want to have in the flat.
These define aspects of proximity relationships between rooms, such as ventilation from the kitchen to the facade.
Internal Minimum Dimensions
The Minimum Dimensions are the regulation requirements that the project must comply with at the geometric level. Some examples would be the diameter of the minimum inscribed circle in the room or the minimum width of the corridors. This is where we introduce all these types of requirements related to regulatory requirements.
We must keep in mind that the minimum size requirements take precedence over the surface size requirements for net areas. In the event of a conflict between them, the room will be sized to meet the minimum required size. This is the case when the area resulting from inscribing the minimum diameter circle is greater than the area required by the user.
General Floor – Design
Most of the customisation options in this section can be grouped into two categories:
Building typology selection
Building typology, Core position or Corridor ends. These define the building typology and the sub-variety that the IA will use to create a layout for the building.
Such as Widthand Length of the building, or others referring to the height, such as Number of standard floors, the Heights of ground and standard floors or of the lift overhead space, or whether we want a Penthouse Floor or not.
Finally, also in this section we have the ability to rotate the building 180º with the Building Orientation button. Or the ability to select theNumber of Coresin the vertical cores typology.
Housing Mix in Standard Floor
Here we define the target housing mix for the standard floors. For each typology from 1 to 4 bedrooms we can customize the housing mix percentage.
The IA will try to stick as closely as possible to this mix within the limitations imposed by the geometry Given the net area and the size of the target dwellings, the resulting number of dwellings may not be a whole integer multiple of the requested mix. It is therefore convenient to think of the housing mix as a guideline. It is an iterative process that can be adjusted quickly according to the results we get.
This is true not only for the standard floor plan but especially when considering the building as a whole. Normally on the ground floor and penthouse floors there are different layouts to those of the standard floor due to the particular characteristics of each floor. We often adjust the layout on the standard floor to take into account the variations that occur on other floors.
Common Areas Dimensions
Here are the configuration options for the common areas, the vertical communication core, stairs and lifts.
Most of the options here fall into three categories:
Core Feature Configuration
Things like the number of lifts, whether we want the staircases to be fire-protected or if split landings are allowed.
Sizing of different common area elements
Such as the minimum widths of communal corridors or access portals to the building. Or the width of the flights of stairs, the width and length of the lift shaft, etc…
Core Morphology Customization
Such as the maximum core height, staircase width and height, or core to façade alignment.
The options in the first two categories are fairly self-explanatory, however those in the last category deserve some explanation.
Maximum core height limits the dimension perpendicular to the building axis that the core is allowed to occupy. It allows us to vary from deep and narrow cores with little facade to shallower and wider cores with more facade.
Stair Width and Stair Height are used to force this dimension into the staircase.
Core to facade alignmentmanages the location of the core relative to the building façade. It can be embedded in the building (if the core dimensioning allows it) or it can protrude.
Terraces – General Floor
Here there are customisation options for 3 different categories:
Overall size of terraces
Such as minimum length of facade with terrace or overhang length.
Overall configuration of terrace design for the building
Such as Percentage of the building’s facade with terrace, Terrace position (relative to the dwelling unit) and Diversity of terrace placement.
Local configuration per facade
This allows us to decide independently for each facade of the building whether we want to have terraces on it or not.
Exterior Enclosure – Parameters
Here we define globally for the building the size of the windows according to the room in which they are. This is done by customizing them with two parameters (per room window): the height of the sill and the width of the opening. The lintel height is always 2,10m.
This can be useful to ensure compliance with certain regulatory requirements, particularly lighting and ventilation requirements.
Construction – Parameters
Here we define globally for the building the thickness of the construction elements, for both vertical walls and horizontal slabs.
The setting of this section has a dramatic impact on the calculation of areas and efficiency ratios. Therefore it is recommended to customize them immediately after creating the building.
It is also very useful for customizing our BIM model in a way that makes it easy for us to progress to a higher definition. So if you are going to request the download of a BIM model it is important to make sure that this section is properly customized.
Sections of the Input Panel for specific floors
There are certain sections that do not appear in the standard floor plan view which is the default view of a building. Their content refers specifically to floors other than the standard one and to customize them we must go to that specific floor. Once there, we can see these new sections in the input panel along with their configuration options. Also, we will be able to see how the changes we made through them take effect.
Ground floor gardens
Similar to the section on terraces on the standard floor but simplified, this allows us to change the size of the Gardens on the ground floor dwellings.
Penthouse floor housing mix
Similar to the housing mix section in the standard floor plan, it allows us to control the housing mix on the penthouse floor.
Penthouse floor setbacks
It allows us to control independently for each facade the setbacks that the penthouse floor must have with respect to the standard floors.
Terraces on the penthouse floor
Similar to the section on terraces on the standard floor but simplified, it allows us to control the size of the terraces on the attic floor.